This release note and the software that accompanies it are copyright (c) 2020, Intel Corporation or its suppliers, and may only be installed and used in accordance with the license that accompanies the software. This Software is furnished under license and may only be used or copied in accordance with the terms of that license. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document. The Software is subject to change without notice, and should not be construed as a commitment by Intel Corporation or its suppliers to market, license, sell or support any product or technology. Unless otherwise provided for in the license under which this Software is provided, the Software is provided AS IS, with no warranties of any kind, express or implied. Except as expressly permitted by the Software license, neither Intel Corporation nor its suppliers assumes any responsibility or liability for any errors or inaccuracies that may appear herein. Except as expressly permitted by the Software license, no part of the Software may be reproduced, stored in a retrieval system, transmitted in any form, or distributed by any means without the express written consent of Intel Corporation. ========================== Supported RAID Controllers ========================== This download supports Intel(R) 34xx/35xx RAID controllers using MR software stack (RMSP3AD160F, RMSP3CD080F, RMSP3HD080E, RSP3TD160F, RSP3MD088F, RSP3DD080F, RSP3WD080E) =================== Package Information =================== Flash package = v51.13.0-3432 ========== Attention! ========== Intel recommends loading Factory Default setting after the firmware upgrade which will not affect data on any existing array. To do so: 1. Reboot the system and login to the RAID BIOS Console. 2. Select the controller and select 'Adapter Properties'->'Next' 3. Set the 'Set Factory Defaults' setting to 'Yes' and submit the change. 4. Reboot the system (the default settings are applied). 5. Re-configure to the desired settings. --------------------------------------- Firmware downgrade notice --------------------------------------- Intel does not recommend to downgrade the factory installed firmware on your RAID module or controller, it has important enhancements and bug fixes you may lose when going to a previous version. If you need to install an older firmware version, please contact Intel for instructions on how to perform this action. ================== Known Restrictions ================== 1) This download does NOT support EFI v1.1 environment. Please use the EFI shell command “ver" which will display the EFI version, to identify the EFI version. 2) When 2 or more VDs are created, VD cache settings must be the same. 3) The default installation of this version of firmware only has formal support for SAS/SATA mode. Support for NVMe mode requires manually changing the controller's profile from 10 to 11. To switch from SAS/SATA mode to NVMe mode on controller 0 at EFI prompt: “storcli.efi /c0 set profile profileid=11” followed by “reset –c” To switch from NVMe mode back to SAS/SATA mode on controller 0 at EFI prompt: “storcli.efi /c0 set profile profileid=10” followed by “reset –c” (as shown by “storcli.efi /cX show profile” the default profile is SAS/SATA, so if you set factory defaults, you will no longer be in NVMe mode on the following DC cycle) ======================= Contents on the package ======================= The following files are included in this zip: Name: Description: 35xx_MR_iMR_FWPKG-51.13.0-3432_Readme.txt This file 35xx_MR_iMR_FWPKG-51.13.0-3432_Release_notes.txt Version and fix information RMSP3AD160F.rom Firmware binary RMSP3CD080F.rom Firmware binary RMSP3HD080E.rom Firmware binary RSP3DD080F.rom Firmware binary RSP3MD088F.rom Firmware binary RSP3TD160F.rom Firmware binary RSP3WD080E.rom Firmware binary License_v2.pdf License Agreement RMSP3AD160F.nsh UEFI firmware update batch file RMSP3CD080F.nsh UEFI firmware update batch file RMSP3HD080E.nsh UEFI firmware update batch file RSP3DD080F.nsh UEFI firmware update batch file RSP3MD088F.nsh UEFI firmware update batch file RSP3TD160F.nsh UEFI firmware update batch file RSP3WD080E.nsh UEFI firmware update batch file StorCLI.efi StorCLI CLI tool for EFI ========================== Installation instructions: ========================== ********************************************************************************************** * NOTE: * * * * If your system uses SAS/SATA expander RES3FV288, RES3TV360, or JBOD2312S3SP. * * Please update the following before proceeding: * * Expander FW to B057 revision (or newer). * * RES3FV288 Expander CPLD to EE revision (or newer) * * RES3TV360 Expander CPLD to AA revision (or newer) * * * * Expander FW and CPLD can be found here: * * https://downloadcenter.intel.com/product/81277/Intel-Storage-Expander-RES3FV288 * * https://downloadcenter.intel.com/product/81278/Intel-Storage-Expander-RES3TV360 * * https://downloadcenter.intel.com/product/86950/Intel-Storage-System-JBOD2312S3SP * * * ********************************************************************************************** UEFI shell instructions for updating RAID Firmware: ----------------- 1. Download and extract all files to a USB flash drive. 2. Boot the target system to EFI shell. 3. Change directory to the local drive and directory containing the flash update files and the firmware image file. 4. Type the name of the .nsh file matching the controller to update (e.g. "RMSP3HD080E.nsh" and press to execute the command - The storcli command line in the .nsh command will default to the first logical RAID contoller ("/c0"). If this there are multiple controllers, the value of controller parameter ("/Cx") will need to be modified to match the specific controller intended for update. 5. Wait for the flash to complete. Do NOT reboot the system during the update. You can also use RAID Web Console 3 or OS version of StorCLI to update the RAID firmware. For more detail, please refer to the Intel(R) RAID Software User's Guide.